Downloads

Aggarwal, D., Sharma, S., & Gupta, M. Impact of Rare Earth Particulates Addition on the Wear Rate of Magnesium Composites with Improved Mechanical and Microstructural Properties for Orthopedic Applications. Progress in Composite Materials. doi: Retrieved from https://test.sciltp.com/testj/pcm/article/view/431
Copyright (c) 2024 by the authors.
Creative Commons License

This work is licensed under a Creative Commons Attribution 4.0 International License.

Article

Impact of Rare Earth Particulates Addition on the Wear Rate of Magnesium Composites with Improved Mechanical and Microstructural Properties for Orthopedic Applications

Divyanshu Aggarwal 1,*, Siddharth Sharma 2 and Manoj Gupta 3,*

1 Department of Mechanical Engineering, Thapar Institute of Engineering and Technology, Patiala 147004, Punjab, India

2 Department of Biotechnology Engineering, Thapar Institute of Engineering and Technology, Patiala 147004, Punjab, India

3 Department of Mechanical Engineering, National University of Singapore, 9 Engineering Drive 1, Singapore 117576, Singapore

* Correspondence: divyanshuaggarwal95@gmail.com (D.A.); mpegm@nus.edu.sg (M.G.); Tel.: +91-8591093067 (D.A.); +65-166358 (M.G.)

Received: 18 July 2024; 22 August 2024; Accepted: 30 August 2024; Published: 9 September 2024

 

Abstract: This study aims to evaluate the wear rate of Mg-Hydroxyapatite-based composites reinforced with rare earth oxide (Neodymium oxide) under in-vitro physiological conditions along with mechanical and microstructural evaluations. To analyze the wear rates of the composites, an innovative technique has been designed to perform experiments on the fabricated samples. The counter disc used for interaction was stainless steel disc coated with the same material as the samples. The analysis was performed under different loading conditions with different sliding velocities considering the different compositions of rare-earth oxide (1%, 1.5%, and 2%). The samples were fabricated via powder metallurgy route with compaction pressure of 250 MPa followed by sintering at 400 °C for 2 Hrs. Moreover, the mechanical analysis was done by calculating the samples’ microhardness and ultimate tensile strength. In contrast, the materials were characterized and synthesized employing FTIR, FESEM, XRD, and EDS techniques. The lowest wear rate was observed when the samples were subjected to higher load and lower velocities. Also, it was found that during progressive wear testing, the wear rate is maximum in the initial stage, but with the increase in sliding distance, the wear rate tends to reduce and then become steady. In addition, it was found that Mg-HA-1.5Nd2O3 showed the highest wear resistance. Moreover, the microhardness of the sample with a rare-earth concentration of 1.5% was higher as compared to other samples. Similar results were obtained for ultimate tensile testing of the composites. FESEM images showed refined microstructure of the samples, with EDS results showing the homogenous distribution of HA and REO particles. XRD analysis showed the development of secondary β-phases that interlocks grain boundaries. Hence, the designed experimental setup provides extensive wear rate results with related conditions created when the implant is placed inside the physiological environment.

Keywords:

Mg-Hydroxyapatite composites neodymium oxide wear analysis mechanical properties microstructure

References

  1. Liu, Y.; Sinha, S.K. Wear performances and wear mechanism study of bulk UHMWPE composites with nacre and CNT fillers and PFPE overcoat. Wear 2013, 300, 44–54. https://doi.org/10.1016/j.wear.2013.01.102.
  2. Moghadasi, M.S.; Mohd Isa, M.A.; Ariffin, M.Z.; Mohd Jamil, S.; Raja, B.; Wu, M.; Yamani, M.R.; Bin Muhamad, F.; Yusof, M.F.; Jamaludin, M.S. et al. A review on biomedical implant materials and the effect of friction stir based techniques on their mechanical and tribological properties. J. Mater. Res. Technol. 2022, 17, 1054–1121. https://doi.org/10.1016/j.jmrt.2022.01.050.
  3. Prasadh, S.; Suresh, S.; Ratheesh, V.; Wong, R.; Gupta, M. Biocompatibility of Metal Matrix Composites Used for Biomedical Applications; Elsevier Ltd.: Amsterdam, The Netherlands, 2021; Volume 1, pp. 474–501. https://doi.org/10.1016/b978-0-12-803581-8.11834-x.
  4. Kumar Balu, S.; Andra, S.; Jeevanandam, J.; Sampath, V. Emerging marine derived nanohydroxyapatite and their composites for implant and biomedical applications. J. Mech. Behav. Biomed. Mater. 2021, 119, 104523. https://doi.org/10.1016/j.jmbbm.2021.104523.
  5. Monticelli, C.; Zucchi, F.; Tampieri, A. Triboelectrochemical behaviour of a Si3N4-TiN ceramic composite and a titanium alloy commonly used in biomedical applications. Wear 2009, 266, 327–336. https://doi.org/10.1016/j.wear.2008.07.005.
  6. Witte, F.; Kaese, V.; Haferkamp, H.; Switzer, E.; Meyer-lindenberg, A. In vivo corrosion of four magnesium alloys and the associated bone response. J. Biomater. 2005, 26, 3557–3563. https://doi.org/10.1016/j.biomaterials.2004.09.049.
  7. Shahabuddin, M.; Mofijur, M.; Rizwanul Fattah, I.M.; Kalam, M.A.; Masjuki, H.H.; Chowdhury, M.A.; Hossain, N. Study on the Tribological Characteristics of Plant Oil-Based Bio-Lubricant with Automotive Liner-Piston Ring Materials. Curr. Res. Green Sustain. Chem. 2022, 5, 1–6. https://doi.org/10.1016/j.crgsc.2022.100262.
  8. Chowdhury, M.A.; Hossain, N.; Masum, A.A.; Islam, M.S.; Shahin, M.; Hossain, M.I.; Shuvho, M.B.A.; Ali, M.R.; Ahmed, A.K.M.F.; Nandee, M.R. Surface Coatings Analysis and Their Effects on Reduction of Tribological Properties of Coated Aluminum under Motion with ML Approach. Mater. Res. Express 2021, 8, 086508. https://doi.org/10.1088/2053-1591/ac1c33.
  9. Chowdhury, M.A.; Reza, M.S.; Hossain, N.; Ali, M.R.; Kowser, M.A.; Shuvho, M.B.A. Improvement of Corrosion Resistance of Galvanization/Nickel/Chrome Plating Low Carbon Steels in H2SO4 under Dynamic Condition. Surf. Topogr. Metrol. Prop. 2021, 9, 035018. https://doi.org/10.1088/2051-672X/ac19f0.
  10. Chowdhury, M.A.; Shuvho, M.B.A.; Hossain, N.; Hassan, M.; Debnath, U.K.; Mia, S. Friction and wear characteristics of ceramics composite under multidirectional motions. Proc. Inst. Mech. Eng. Part J J. Eng. Tribol. 2022, 236, 867–880. https://doi.org/10.1177%2F13506501211042146.
  11. Gu, X.; Zheng, Y.; Cheng, Y.; Zhong, S.; Xi, T. Biomaterials In vitro corrosion and biocompatibility of binary magnesium alloys. Biomaterials 2009, 30, 484–498. https://doi.org/10.1016/j.biomaterials.2008.10.021.
  12. Aggarwal, D.; Kumar, V.; Sharma, S. Effect of rare earth oxide microparticles on mechanical, corrosion, antibacterial, and hemolytic behavior of Mg-Hydroxyapatite composite for orthopedic applications–A preliminary in-vitro study. J. Biomed. Mater. Res. Part B Appl. Biomater. 2023, 111, 1232–1246. https://doi.org/10.1002/jbm.b.35228.
  13. Adekanmbi, I.; Mosher, C.Z.; Lu, H.H.; Riehle, M.; Kubba, H.; Tanner, K.E. Mechanical behaviour of biodegradable AZ31 magnesium alloy after long term in vitro degradation. Mater. Sci. Eng. C 2017, 77, 1135–1144. https://doi.org/10.1016/j.msec.2017.03.216.
  14. Manakari, V.; Parande, G.; Doddamani, M.; Gupta, M. Evaluation of wear resistance of magnesium/glass microballoon syntactic foams for engineering/biomedical applications. Ceram. Int. 2019, 45, 9302–9305. https://doi.org/10.1016/j.ceramint.2019.01.207.
  15. Mu, J.; Wang, H.; Qin, B.; Zhang, Y.; Chen, L.; Zeng, C. Improved wear and corrosion resistance of biological compatible TiZrNb films on biomedical Ti6Al4V substrates by optimizing sputtering power. Surf. Coat. Technol. 2021, 428, 127866. https://doi.org/10.1016/j.surfcoat.2021.127866.
  16. Chirico, C.; Romero, A.V.; Gordo, E.; Tsipas, S.A. Improvement of wear resistance of low-cost powder metallurgy β-titanium alloys for biomedical applications. Surf. Coat. Technol. 2022, 128207. https://doi.org/10.1016/j.surfcoat.2022.128207.
  17. Qiu, M.; Li, Y.; Chen, L.; Bai, Y. Effects of rare earth treatment on tribological properties of self-lubricating spherical plain bearings. Wear 2013, 305, 274–279. https://doi.org/10.1016/j.wear.2012.12.021.
  18. Tatarko, P.; Kašiarová, M.; Chlup, Z.; Dusza, J.; Šajgalík, P.; Vávra, I. Influence of rare-earth oxide additives and SiC nanoparticles on the wear behaviour of Si3N4-based composites at temperatures up to 900 °C. Wear 2013, 300, 155–162. https://doi.org/10.1016/j.wear.2013.01.030.
  19. Tatarko, P.; Kašiarová, M.; Dusza, J.; Morgiel, J.; Šajgalík, P.; Hvizdoš, P. Wear resistance of hot-pressed Si3N4/SiC micro/nanocomposites sintered with rare-earth oxide additives. Wear 2010, 269, 867–874. https://doi.org/10.1016/j.wear.2010.08.020.
  20. Jäger, M.; Jennissen, H.P.; Dittrich, F.; Fischer, A.; Köhling, H.L. Antimicrobial and osseointegration properties of nanostructured titanium orthopaedic implans. Materials 2017, 10, 1–28. https://doi.org/10.3390/ma10111302.
  21. Stemmer, P.; Fischer, A. Pathways of dissipation of frictional energy under boundary lubricated sliding wear of martensitic materials. Lubricants 2018, 6, 34. https://doi.org/10.3390/lubricants6020034.
  22. Subramanian, S.M.; Vijayan, J.; Muthaiah, V. Tribological wear behaviour and hardness measurement of SiC, Al2O3reinforced Al. matrix hybrid composite. J. Inst. Eng. 2017, 98, 291–296. https://doi.org/10.1007/s40033-016-0134-8.
  23. Lembang, M.S.; Yulizar, Y.; Sudirman, S.; Apriandanu, D.O.B. A Facile Method for Green Synthesis of Nd2O3 Nanoparticles Using Aqueous Extract of Terminalia Catappa Leaf. AIP Conf. Proc. 2018, 2023, 1–7. https://doi.org/10.1063/1.5064090.
  24. Ahmadi, S.; Mohammadi, L.; Rahdar, A.; Rahdar, S.; Dehghani, R.; Igwegbe, C.A.; Kyzas, G.Z. Acid Dye Removal from Aqueous Solution by Using Neodymium(III) Oxide Nanoadsorbents. Nanomaterials 2020, 10, 556. https://doi.org/10.3390/nano10030556.
  25. Chandrasekar, A.; Sagadevan, S.; Dakshnamoorthy, A. Synthesis and characterization of nano-hydroxyapatite (n-HAP) using the wet chemical technique. Int. J. Phys. Sci. 2013, 8, 1639–1645. https://doi.org/10.5897/IJPS2013.3990.
  26. Gheisari, H.; Karamian, E.; Abdellahi, M. A novel hydroxyapatite -Hardystonite nanocomposite ceramic. Ceram. Int. 2015, 41, 5967–5975. https://doi.org/10.1016/j.ceramint.2015.01.033.
  27. Pramanik, S.; Agarwal, A.K. Development of High Strength Hydroxyapatite for Hard Tissue Replacement. Trends Biomater. Artif. Organs 2005, 19, 46–51. https://doi.org/10.1016/j.ceramint.2005.10.025.
  28. Ibrahim, A.; Magliulo, N.; Groben, J.; Padilla, A.; Akbik, F.; Hamid, Z.A. Hardness, an Important Indicator of Bone Quality, and the Role of Collagen in Bone Hardness. J. Funct. Biomater. 2020, 11, 85. https://doi.org/10.3390/jfb11040085.
  29. Alijani, S.; Anvari, A. Characterization of Implantation’s Biomaterials Based on the Patient and Doctor Expectations. Res. Med. Eng. Sci. 2018, 4, 315–316. https://doi.org/10.31031/RMES.2018.04.000583.
  30. Wang, X.; Chen, G.; Yang, W.; Hussain, M.; Wang, C.; Wu, G.; Jiang, D. Effect of Nd content on microstructure and mechanical properties of Grf/Al composite. Mater. Sci. Eng. A 2011, 528, 8212–8217. https://doi:10.1016/j.msea.2011.07.039.
  31. Zohoor, M.; Givi, M.K.B.; Salami, P. Effect of processing parameter on fabrication of Al-Mg/Cu composites via friction stir processing. Mater. Des. 2012, 39, 358–365. https://doi.org/10.1016/j.matdes.2012.02.042.
  32. Hossieni, S.A.; Ranjbar, K.; Dehmolaei, R.; Amirani, A.R. Fabrication of Al5083 surface composites reinforced by CNTs and cerium oxide nano particles via friction stir processing. J. Alloy. Compd. 2015, 622, 725–733. https://doi.org/10.1016/j.jallcom.2014.10.158.
  33. Kujur, M.S.; Manakari, V.; Parande, G.; Prasadh, S.; Wong, R.; Mallick, A.; Gupta, M. Development of rare-earth oxide reinforced magnesium nanocomposites for orthopaedic applications: A mechanical/immersion/biocompatibility perspective. J. Mech. Behav. Biomed. Mater. 2021, 114, 104162. https://doi.org/10.1016/j.jmbbm.2020.104162.
  34. Zhang, Z.; Chen, D.L. Consideration of Orowan strengthening effect in particulate-reinforced metal matrix nanocomposites: A model for predicting their yield strength. Scr. Mater. 2006, 54, 1321–1326. https://doi.org/10.1016/j.scriptamat.2005.12.017.
  35. Gerhardt, L.; Boccaccini, A.R. Bioactive Glass and Glass-Ceramic Scaffolds for Bone Tissue Engineering. Materials 2010, 3, 3867–3910. https://doi.org/10.3390/ma3073867.
  36. Henkel, J.; Woodruff, M.A.; Epari, D.R.; Steck, R.; Glatt, V.; Dickinson, I.C.; Hutmacher, D.W. Bone Regeneration Based on Tissue Engineering Conceptions—A 21st Century Perspective. Bone Res. 2013, 1, 216–248. https://doi.org/10.4248/BR20130300.
  37. Sunil, B.R.; Reddy, G.P.K.; Patle, H.; Dumpala, R. Magnesium based surface metal matrix composites by friction stir processing. J. Magnes. Alloy 2016, 4, 52–61. https://doi.org/10.1016/j.jma.2016.02.001.
  38. Chen, J.; Tan, L.; Yu, X.; Etim, I.P.; Ibrahim, M.; Yang, K. Journal of the Mechanical Behavior of Biomedical Materials Mechanical properties of magnesium alloys for medical application: A review. J. Mech. Behav. Biomed. Mater. 2018, 87, 68–79. https://doi.org/10.1016/j.jmbbm.2018.07.022.
  39. Noviana, D.; Paramitha, D.; Fakhrul, M.; Hermawan, H. ScienceDirect The effect of hydrogen gas evolution of Magnesium implant on the postimplantation mortality of rats. J. Orthop. Transl. 2016, 5, 9–15. https://doi.org/10.1016/j.jot.2015.08.003.
  40. Zhao, D.; Wang, T.; Kuhlmann, J.; Dong, Z.; Chen, S.; Joshi, M.; Salunke, P.; Shanov, V.N.; Hong, D.; Kumta, P.N.; et al. In vivo monitoring the biodegradation of Magnesium alloys with an electrochemical H2 sensor. ACTA Biomater. 2016, 36, 361–368. https://doi.org/10.1016/j.actbio.2016.03.039.
  41. Sharma, V.K.; Kumar, V.; Joshi, R.S. Effect of RE addition on wear behavior of an Al-6061 based hybrid composite. Wear 2019, 426–427, 961–974. https://doi.org/10.1016/j.wear.2019.01.044.
  42. Khan, S.; Candidate, S.M. Hydrophobicity of Rare-Earth Oxide Ceramics and Their Application in Promoting Sustained Dropwise Condensation and Corrosion and Fouling Mitigation in Hydropower Systems. 2015. Available online: https://www.osti.gov/servlets/purl/1638709 (accessed on 22 Dec 2022).
  43. Sharma, V.K.; Kumar, V.; Joshi, R.S. Parametric study of aluminium-rare earth based composites with improved hydrophobicity using response surface method. J. Mater. Res. Technol. 2020, 9, 4919–4932. https://doi.org/10.1016/j.jmrt.2020.03.011.
  44. Hass, K.C.; Schneider, W.F.; Curioni, A.; Andreoni, W. The chemistry of water on alumina surfaces: Reaction dynamicsfrom first principles. Science 1998, 282, 265–268. https://doi.org/10.1126/science.282.5387.265.
  45. Cohen, N.; Dotan, A.; Dodiuk, H.; Kenig, S.; Cohen, N.; Dotan, A.; Dodiuk, H.; Kenig, S.; Gan, R. Superhydrophobic Coatings and Their Durability Superhydrophobic Coatings and Their Durability. Mater. Manuf. Process. 2016, 31, 1143–1155. https://doi.org/10.1080/10426914.2015.1090600.
  46. Aggarwal, D.; Kumar, V.; Sharma, S. Effect of rare earth oxide microparticles on mechanical, corrosion, antibacterial, and hemolytic behavior of Mg-Hydroxyapatite composite for orthopedic applications–A preliminary in-vitro study. J. Biomed. Mater. Res. Appl. Biomater. 2023, 111, 1232–1246. https://doi.org/10.1002/jbm.b.35228.